EMC QLogic Installation Guide Page 18
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
16
EMC Fibre Channel and iSCSI with QLogic Host Bus Adapters in the Windows Environment
Installation and Configuration
How this guide works
In an effort to simplify the installation and configuration of QLogic
Fibre Channel HBAs, this guide follows a simple flow chart, as
shown in Figure 1 on page 17, that guides you through the necessary
procedures to connect your Windows server to EMC storage arrays.
Tips on planning, miscellaneous procedures, and troubleshooting
information are located in Chapter 2, ”Miscellaneous Planning and
Procedures,” and Chapter 3, ”Troubleshooting.”
This document will guide you through the following steps:
1. “Installing the HBA” on page 18
2. “Booting from the external storage array” on page 24:
a. If not installing an IA-64 or EFI-based server:
– “Create a floppy disk with the EMC-approved driver and
BIOS” on page 24.
– “Install/upgrade firmware and boot BIOS from DOS” on
page 25.
– “QLogic Fibre Channel HBA BIOS/boot LUN settings” on
page 26.
– “Verifying array/LUN visibility for boot” on page 49.
b. If installing an IA-64 or EFI-based server:
– “Installing a RAMDISK under the EFI shell” on page 49
3. “Installing the Windows operating system” on page 51.
4. “Installing HBA driver and software utilities” on page 69.
5. “Verifying connectivity to the storage array” on page 81.
Downloading latest QLogic drivers/firmware/BIOS files
Throughout this document, there are references to updated files from
QLogic. All of the versions included on the QLogic CD packaged
with your HBA are current as of this documents release. However,
there may be updates to these files that may be necessary to
download. For these, use the QLogic website,
http:///www.qlogic.com. From the main page on the QLogic
website, click Downloads link on the left side of the page. On the
resulting support page, click the EMC link under the OEM Models
section. On the resulting page, click the EMC Array category for your
- Windows Environment 1
- Contents 3
- Chapter 3 Troubleshooting 5
- Courier italic 15
- Installation and 17
- Configuration 17
- How this guide works 18
- Verify Array/LUN 19
- Visibility for Boot 19
- Installing the HBA 20
- STOP: 0X0000007B 21
- HBA edge connecters 23
- PCI Express slots 24
- PCI Express slots aligned 24
- QLogic banner 29
- Main Fast!UTIL options window 30
- Configuration Settings window 30
- Adapter Settings window 31
- Enter 34
- Warning dialog 35
- Fast!UTIL Options window 36
- Firmware boot manager menu 38
- refer to memory ramdisks 39
- QLogic directory 41
- EFIutil.efi 41
- QLogic efiutil all upgrade 43
- QLogic Fibre Channel drivers 45
- Driver handle numbers 46
- -s 5f 62 46
- Edit adapter settings 47
- Connection option 48
- Figure 32 Options set 50
- RAMDISK 51
- Windows 52
- HBA selection screen 57
- Windows setup screen 58
- Base article Q240672.) 59
- Existing partitions 59
- Windows Boot Manager 62
- Windows Setup screen 62
- Windows Install screen 63
- Loading driver screen 66
- Browse for Folder screen 67
- A as shown in Figure 47 67
- Install Windows screen 70
- Pre-installation guidelines 71
- Driver installation/upgrade 72
- SANsurfer driver selection 74
- Post-installation procedures 78
- SANsurfer HBA install wizard 79
- Show SAN 82
- SANsurfer icon 83
- Connect to the host 84
- ServerManager: 85
- <sp_IP> 88
- <storagegroupname> 88
- Miscellaneous 91
- Planning and 91
- Procedures 91
- Download Firmware dialog box 97
- F1 to enter the server BIOS 112
- Enter. This boot device 112
- Blade server restrictions 113
- Driver revision 114
- Where to find the driver 115
- Windows 2003 STORPort updates 116
- STORPort drivers 117
- A:\, for 120
- QLogic advanced utilities 123
- Utilities tabbed page 125
- EMC CLARiiON storage arrays 127
- Set the HBA FC-AL loop ID 130
- Reconfigure the HBA jumper 133
- Troubleshooting 135
- Volume sizes 136
- Host after the rebooted 141
- Known issues 142
- Problems and solutions 143
- Problem 4 144
- Problem 5 144
- Problem 6 144
- Problem 7 145
- Problem 8 145
- Problem 9 145
- Third-Party Software 147
- SANsurfer version history 148
© 2020, manymanuals.com. All rights reserved. | 1.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals